BLACK WEEK

Brew Cooler XL 30L Fermenter Bag - for fermenter or kegs

Brew Cooler XL 30L Fermenter Bag - for fermenter or kegs

The Brew Cooler XL is an extra large waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters and kegs up to 30L. Either one 30L fermenter or two cornelius kegs fits inside. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler XL worksThe function is simple, place your fermenter or keg(s) inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler XL 30L specificationsHeight: 70 cmLength 40 cmWidth: 40 cmInternal supports: 60cm Vertical rib supports keeps the bag upright by itself.Material: Tough black polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.Note: Fermenters, kegs or other accessories are not included.

349 kr
280 kr per piece when you buy 2 or more
Brewly Belgian Abbey Ale 12g Yeast

Brewly Belgian Abbey Ale 12g Yeast

Special strain from a well known Belgian Abbey, perfect for fermentation of all kinds of Abbey ale; Blondes, Dubbel, Tripel and Quadruple - as well as Belgian pale- and strong ales. It offers fruity amazingly complex esters, subtle phenolics and very clean character.- Alcohol Tolerance: Medium (10%)- Temperature Range: 15-25°C (59-77°F)- Attenuation: Medium (73-77%) - Flocculation: Medium- Net Weight: 12g (0.42oz) - Made in EU.- GMO-Free: Yes- Storage: In fridge (cool & dry)- Packed in a protective atmosphere.UseSprinkle the yeast directly in up to 23 liters (6 gallons) of wort. Alternatively, rehydrate the yeast. Aerate. If Original Gravity is above 1.065 (65 °Öchsle), use 2 packs for 23L.Ingredients:Yeast, emulsifier E491

21 kr
17 kr per piece when you buy 2 or more
Brewly CF & CCF 30L Conical Insulation Jacket

Brewly CF & CCF 30L Conical Insulation Jacket

Insulation jacket for the Brewly 30L Conical Fermenter (both versions, CF & CCF). Material: 5 mm neoprene foam.

280 kr
175 kr
Brewly Weissbier Ale 12g Yeast

Brewly Weissbier Ale 12g Yeast

This special yeast strain has its origin in Bavaria, Germany. It is especially used to produce German wheat beer styles like Hefeweissen/Weiss beer. It can be used to produce any kind of wheat beer including American Wheat and Belgian Wit. The final aroma is very estery, rich in flavours of phenolic aromas of banana and clove.Brewly Weissbier Ale Yeast- Alcohol Tolerance: High (12%)- Temperature Range: 12-25°C (53-77°F)- Attenuation: High 80%- Flocculation: Low- Net Weight: 12g (0.42oz)- GMO-Free: Yes- Storage: In fridge (cool & dry)- Packed in a protective atmosphere.- Made in EU.UseSprinkle the yeast directly in up to 23 liters (6 gallons) of wort. Alternatively, rehydrate the yeast. Aerate. If Original Gravity is above 1.065 (65 °Öchsle), use 2 packs for 23L.Ingredients:Yeast, emulsifier E491

25 kr
21 kr per piece when you buy 2 or more
Brewolution Chiller 40 - 8,8 meter spiral

Brewolution Chiller 40 - 8,8 meter spiral

Brewolution Chiller 8,8m in Stainless Steel with optimized distance between the spirals for faster cooling of the wort. Suitable for breweries, pots and kettles up to 40L. Fits 3/8" pushfit fittings, perfect for hose with 3/8" (9,5mm) outer diameter. Fittings and hose not included.Diameter 25 cm.Height 37 cm.

489 kr
Brewski T-Shirt Navy/Black

Brewski T-Shirt Navy/Black

Stylish Navy T-shirt with the Brewski logo in Black screen print for a subtle support of your favorite brand. Made of 100% soft, ringspun cotton with a lovely fit. Wash at 40° inside and out for best durability.

210 kr
Brewski T-Shirt White

Brewski T-Shirt White

Stylish White T-shirt with the Brewski logo in black screen print. Made of 100% soft, ringspun cotton with a lovely fit. Wash at 40° inside and out for best durability.

210 kr
Brewster Dominator 25L Extension Kit - Upgrade your Dominator Brewery

Brewster Dominator 25L Extension Kit - Upgrade your Dominator Brewery

Fits both Dominator och Dominator PRO. Upgrade your Brewolution Brewster Dominator to a 65-litre system for bigger batches and bold beers. This setup lets you brew approximately 50 litres of finished beer, and with a 20 kg malt capacity, you can craft larger batches, bolder beers, and have endless possibilities! Premium Quality for the Best Value. Brew approx. 50 L. beer The grain basket can hold an impressive 20 kg of malt Brew 2 x 25 All-Grain-Kits Easily upgrade to a 65-litre brew system Kit includes all you need Easily upgrade the Brewster Dominator 40-litre system to a 65-litre capacity with this extension kit. Premium Quality for the Best Value. This setup allows you to brew approximately 50 litres of finished beer, offering greater flexibility for larger batches. The grain basket can hold an impressive 20 kg of malt, giving you the potential to craft seriously bold, high-gravity beers. Even with a smaller 25-litre batch, you can brew a truly robust beer by using the full 20 kg malt capacity. Brewster Dominator Extension Kit 25 includes:- Boiler Extension 25 L- Grain Basket Extension 47 L- Recirculation Pipe Extension- Sight Glass Extension with Stainless Steel Shield- Silicone Seal for Boiler Extension

2 098 kr
1 398 kr
Cannular Semi-Auto Pro Can Seamer

Cannular Semi-Auto Pro Can Seamer

The Cannular is a Semi-Auto Pro Model that makes canning easier. Now you don't even have to pull a lever back and forth to seam the can. The seaming process takes only 3 Seconds!  That's crazy fast. No spacers are needed for different cans. NOTE: CDL 202 can lids Only.In its standard design the Cannular Semi-Auto can handle 33 cl and 50 cl aluminium cans with can ends type CDL 202. Whether you're a cool bar wanting to fill your own crowlers or you are a home brewer wanting to keep your home brew fresh and protected from damaging light, the Cannular is the answer.  The Cannular can seamer is one of the most compact and easy to use benchtop can seamers around.  With a single operator you can seam/seal the cans in 3 seconds meaning this compact machine is suitable for small breweries or brewpubs doing small production runs.Semi-Auto DesignThis new Semi-Auto Model of can seamer is able to guarantee you get a consistent seaming process every time. Unlike our less expensive manual can seamer this machine has no lever meaning it's even easier for the operator to seam the can consistently and will not vary on how hard the operator is pulling the lever.  Once the machine is tuned only a small amount of oil on the bearings is required and no other maintenance for 50,000 cans.  Safe To Use with Low Voltage Power SupplyIf you have ever used a can seamer you would know that you can sometimes spill liquids while processing cans.  As a result, we have made the Cannular machine with 24v DC so even when you make a mess you don't have a risk of electrocuting yourself.  This also makes the machine easier to clean and wash down.Environmentally FriendlyWhen compared with disposable glass bottles cans are much more environmentally friendly as they are:* Significantly lighter making them less energy-consuming to transport* More recyclable, more cost-effective to recycle, and a higher percentage of cans get recycled in Australia when compared with glassGreat For Outdoor EventsCans are a fantastic choice for outdoor events, parties, pool events, or at the beach.  Broken glass can be dangerous and difficult to clean up completely. Cans on the other hand are the safest choice in this respect.Preserve the Products Quality and FreshnessGas Barrier - Although a glass bottle is completely airtight, the crown seals allows a small migration of CO2 out of the beverage and allows small amounts of oxygen to get ingress as the rubber seal is permeable.  So as a packaging solution glass bottles are imperfect and the product quality will degrade more rapidly due to this gas migration. Aluminium cans have a hermetic metal on metal seal that is impervious to gas transmission.Light Block - Many beverages especially beer can get damaged quickly due to light.  If you expose many beers to sunlight for even 5 minutes the beer can become light damaged ("skunked").  Even softer light such as indoor lights will damage beer over time and noticeable skunking can occur with both incandescent and fluorescent light globes within hours.  So unless you keep your glass bottles in the dark all the time you will compromise the beer quality.  Aluminium cans solve this problem by blocking 100% of damaging light.InfoMotor: 24V(DC). AC adapter included (Anderson plug type 40A).Powered by: 220 - 240 V (AC) / 50 - 60 HzRotational speed: over 3300 rpmHeight adjustment: 60 - 200 mm, (no need to use different spacers for different can heights)Size:355 mm deep230 mm wide495 mm heighWeight: 28 kg

5 941 kr
DigiBoil 65L Digital Turbo Boiler

DigiBoil 65L Digital Turbo Boiler

Digiboil 65L is a digital electric boiler for heating brewing and sparging water, or as a BIAB-kettle. Suitable for heating up to 60 liters of water. Switch on the heating of the sparge water at mash-in, and you'll know it will be ready to use when you need it for sparging. Once the set temperature is reached, the DigiBoil will hold that temperature autmatically.Clearly visible volume graduations in Litres and Gallons. Easily accessible display and power switches at the side of the kettle. The temperature is adjustable between 0°C and 140 °C, in increments of 1 °C.DigiBoil 65L Digital Turbo Boiler- Three built-in heating elements for easy cleaning- Adjustable effect in 7 steps: 0,5 kW to 3,5 kW- Stainless Steel tap with 13 mm hose barb and 1/2" BSP threaded fitting- Suitable as boiler, HLT (Hot Liquor Tank) and for BIAB-brewing- Can also be used for cooking Sous Vide- Capacity: 60 Liters- Power: 3.5 kW (heating elements 2 kW + 1 kW + 0.5 kW). EU-plug (UK plug is not included).- Weight: 13 kg- Height: 74 cm- Diameter: 42 cm

2 654 kr
2 517 kr
Kegland BlowTie Kit Integrated Gauge (0-15psi)

Kegland BlowTie Kit Integrated Gauge (0-15psi)

Fully assembled kit with Ball lock coupling and overpressure valve with manometer. If you want to ferment under pressure on e.g. FermZilla, this is the solution for you! The adjustment screw on the valve makes it easy to increase or decrease the set pressure.The parts can be easily disassembled for cleaning. Kegland BlowTie Kit Integrated Gauge (0-15psi) Includes: 1x BlowTie 2 Spunding Valve with 0-15psi pressure gauge (can be replaced)1x Duotight 8mm (5/16") Ball Lock for CO21x Intermediate piece 8mm (5/16")

231 kr
Kegland BlowTie Spunding Valve Kit (0-15psi)

Kegland BlowTie Spunding Valve Kit (0-15psi)

This kit has been designed for simplicity and ease of putting together. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job. The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure. This BlowTie unit can be easily disassembled for cleaning using a Phillips head screwdriver. Instructions:Use the yellow adjustment knob to control the pressure coming out of the pressure vessel.  Clockwise is higher pressure and anticlockwise is lower pressure.We would recommend gassing a keg to a known pressure e.g. 15psi then attach your Blow Tie Kit to the keg and adjust to 10psi. Specifications:1. Made from food-grade acetal2. Stainless screws3. 8mm (5/16") push on both sides4. 0-15psi pressure ratingPlease note: The joiners are a semi-permanent fitting. You will not be able to remove the fittings easily. If you would like to have a completely removable fitted kit we would suggest using EVABarrier 4mm ID or 5mm ID hose as the joining pieces. This Kit Includes:1 x KL03643 BlowTie Diaphragm Spunding Valve1 x KL02387 duotight – 8mm (5/16”) Female x 8mm (5/16”) Female Double Tee Piece1 x KL06880 duotight – 8mm (5/16”) Female x FFL Female Thread1 x KL14816 8mm Push In Pressure Gauge 0-15psi1 x KL02967 Premium Ball Lock Disconnect (MFL) Grey/Gas2 x KL18012 8mm Rigid Plaster Joiner With pressurised fermentation becoming ever more popular it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process.  The BlowTie has been designed specifically for this reason. For more information about the many benefits of pressure fermentation please see this article. Pressure TransfersWhen transferring from keg to keg, keg to bottle, or fermenter to keg it's often a good idea to have head pressure in the keg you are filling into especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process. Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation.  Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.The BlowTie has been made completely differently taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure.

231 kr
Kegland CIP Spinning Spray Rotor Low Volume

Kegland CIP Spinning Spray Rotor Low Volume

Kegland "Little Red Spitfire" KL04329 CIP Spinning Spray Rotor is a low volume, inexpensive low-flow spray head for low voltage pumps as low as 6W up to 25W. The perfect spray head that has multiple uses over your brew day. 1/2" BSP thread. 300 mm length silicon. Stainless nut and barb. - Clean In Place (CIP) with your 35L, 65L or 100L BrewZilla (can be fitted to the other branded units) What can it do?- Clean In Place your 35L, 65L or 100L BrewZilla. Simply cut your recirculation hosing, or purchase additional silicone hosing to get the right length for your setup. You will be able to find the optimum length required by testing with water first. We found great success using the glass lid to start with to see if it is coating everything that you need it to. Specification 1 x Custom molded rotating spray head with 1/2" BSP thread1 x 300mm length silicon tubing suitable for your BrewZilla recirculation arm1 x Stainless nut and barb Please note: The rotating spray head can only be used in the downwards position, it cannot be tilted or mounted sideways or upside down.

91 kr
Kegland Duotight Inline Regulator - 1/4" (6.35mm) - 0-10bar (0-150psi)

Kegland Duotight Inline Regulator - 1/4" (6.35mm) - 0-10bar (0-150psi)

This awesome compact solution for adjusting water and gas pressure can be useful in many different applications.  With Manometer 0-10 bar (0-150 psi). This can be used for compressed air, CO2, nitrogen, mains water supply and many other things.The unit is made from food grade engineering plastic, stainless steel and quality made EPDM seals. These compact inline regulators have been designed to suit 8mm (5/16") Evabarrier Tubing.  For higher pressures such as mains water supply we recommend the 4mm ID Tubing here or 5mm ID here if you do not need as high pressures and you would prefer higher flow rate.Suits pressures 0-150psi (0-10 bar)Suitable for mains water pressureSuitable for liquid or gasMade from Acetal/POM, EPDM o-rings and stainless teethSuits 6.35mm (1/4") OD Tubing such as our Evabarrier TubingIncludes integrated manometer 0-10 bar (0-150 psi) Pressure Gauge

137 kr
Kegland MK4 Dual Pressure Type 30 CO2 Regulator

Kegland MK4 Dual Pressure Type 30 CO2 Regulator

Dual Pressure CO2 regulator MK4. Precise regulator of high quality. These are 2 MK4 regulators that are connected together, so that you get 2 outputs with individual pressure adjustment.  Thread type for connecting CO2 bottle: Type 30 (Australia/NZ), compatible with Nordic CO2 standard DIN-477 No. 6 / W 21.8 x 1/14" The outputs have 1/4" MFL threads, and it comes with 2 DuoTight (pushfit) adapters for 8mm (5/16") hose.  Recommended range of use: 0 to 3.5 bar

909 kr
Magnetic Stirrer 8W 0-1500 RPM

Magnetic Stirrer 8W 0-1500 RPM

Easy-to-use magnetic stirrer with good capacity of 1,5 liters (and more). Infinitely variable speed and durable construction that can withstand a little spill.Material: Durable cover.Speed: 0-1500 rpm.Capacity: 1.5 liters.Power supply: 230VMax Power: 8W

556 kr
384 kr