Other

Plastic pipette 3ml

Plastic pipette 3ml

Affordable disposable plastic pipette with graduation 0,5-3ml.

2 kr
Temporarily out of stock
View product
Plastic pipette long 1,5ml

Plastic pipette long 1,5ml

Extra long 1,5ml disposable pipette with graduation.

2 kr
Plastic pipette 3ml 10-pack

Plastic pipette 3ml 10-pack

Plastic pipette 3ml 10-pack

17 kr
Plastic Pipette 3ml 25-pack

Plastic Pipette 3ml 25-pack

Affordable disposable plastic pipette with graduation 0.5 - 3 ml. Material: polyethylene. Length: 160 mm. Graduation: 0.5 - 3 ml.

27 kr
Temporarily out of stock
View product
Plastic container with lid 50ml

Plastic container with lid 50ml

Plastic container with lid 50mlMaterial: Polypropylene plastic with polyethylene snap cap (LDPE). Dimensions: Height 5 cm, the diameter of the opening 4 cm.

6,8 kr
Temporarily out of stock
View product
Plastic container with lid 215ml

Plastic container with lid 215ml

Plastic container with lid 215ml. Made in Polypropylene plastic with snap cap of polyethylene (LDPE). Plastic container with lid 215mlHeight: 3 cmDiameter: 10 cm.Quantity: 1pc

20 kr
Temporarily out of stock
View product
Milwaukee MW700 PRO Lux (Light) Meter

Milwaukee MW700 PRO Lux (Light) Meter

The MW700 is a portable Lux meter designed to perform light measurements from 0 to 50000 Lux. This handy and ergonomically designed Lux meter is ideal for anyone looking for fast and reliable light measurements. This meter is suitable for a wide range of application. Note that the sensor is NOT waterproof.Average indoor lighting ranges from 100 to 1000 Lux and average outdoor sun lights about 50000 Lux. Lux is a unit that indicates the density of light that falls on a surface.The human eye is sensitive only to blue, green, and red light, so in calculating the Lux falling on an object, only the light that the human eye sees is counted. When only infrared light falls on an object, the Lux is counted as zero since our eyes see nothing. Mathematically, a spectral weighting function becomes convolved with the actual illumination spectrum to calculate Lux exactly.This is the formal definition of Lux and it makes Lux an unusual unit of measure. Still, Lux can be thought of as a way of measuring light in terms of what our eyes perceive. The metric unit of measure for luminance of a surface. One Lux is equal to one Lumen per square meter. One Lux equals 0.0929 footcandles. DESIGN FEATURESFast, easy-to-read results with large digital LCD readout, silicon photodiode sensor attached to a 4.4' cable, Three resolution settings - 1, 10, and 100 Lux, Accuracy to ±6% of reading ±1 digitLightweight and portable, 150 hours of battery life with continuous use (battery included) with low battery warning.SPECIFICATIONS Milwaukee MW700 PRO Lux (Light) MeterRange: 0.000 to 1999 Lux; 2000 to 19999 Lux; 20000 to 50000 LuxRange Setting: Manual through key buttonsResolution: 0.000 to 1999 Lux: ±1 Lux; 2000 to 19999 Lux - ±10 Lux; 20000 to 50000 Lux - ±100 LuxAccuracy: ±6% of reading ±1digitsPeak wave length: 560 (nm)Sensor type: Silicon Photodiode (connected to meter)Sensor sensitivity: 100 scotopic LUXSensor stability: ±2% change per year (in first two years)Environment: 0 to 50°C / 32 to 122°F; max RH 95%Battery Type: 1 x 9V alkalineBattery Life: Approx. 150 hours of continuous useAuto-off: after about 5 minutes of non-useDimensions: 5.6 x 3.1 x 1.25 inchesWeight (meter with sensor): 9.5 ounces

746 kr
Milwaukee MW802 PRO 3-in-1 pH, EC, TDS Combo Meter with ATC

Milwaukee MW802 PRO 3-in-1 pH, EC, TDS Combo Meter with ATC

The Milwaukee MW802 PRO Combo Meter lets you easily and accurately test pH, conductivity (EC) and total dissolved solids (TDS) using a single meter and integrated probe.Simple, portable and rugged. No more juggling multiple electrodes and wires. Automatic temperature compensaton included. The MW802 is the ultimate solution for pH and nutrient management.Specifications:pH Range: 0.00 to 14.00 pHEC Range: 0.00 to 6.00 mS/cmTDS Range: 0 to 4000 ppmpH Resolution: 0.1 pHEC Resolution: 0.01 mS/cmTDS Resolution: 10 ppmpH Accuracy: ±0.2EC/TDS Accuracy: ±2% Full ScaleCalibration Solutions: M10007 (pH 7.01) M10032 (1382 ppm) M10442B 1500 ppmConversion Factor: 0.68Calibration: Manual at 1 pointTemperature Compensation: Automatic from 0 to 50°CProbe: SE600 combination pH/EC/TDS probeEnvironment: 0 to 50°C / 32 to 122°F; max RH 95%Battery Type / Battery Life: 1 x 9V alkaline / 150 hours of useAuto-off: After 8 minutes of non-useDimensions: 7.3 x 3.2 x 1.8 inchesWeight: 5.8 ounces (with battery)pH and conductivity are critical for growers. pH can effect plant nutrient and water uptake and reduce the efficiency of fertilizer, herbicides and pesticides. Managing conductivity helps growers pinpoint fertilizer and other needs.DESIGN FEATURES- The design of the MW802 is focused on simple operation and ruggedness. With a single probe, big screen, easy calibration, the MW802 is exceptionally simple to operate.- A tough meter build and a rugged but replaceable probe means that you can expect years of use.- The Milwaukee PRO Combo meter offers:pH, conductivity / nutrient EC, TDS (ppm) with automatic temperature compensation.A replaceable, integrated pH, EC, and TDS (ppm) probe with a single 3 foot cable for easy use (SE600 probe included).A fiber junction on the pH sensor to reduce contamination when measuring fertilizer solutions.A light weight and portable form factor at just 5.8 ounces with battery and just over 3 inches wide.A large easy to read display.Factory calibration with a simple, single point manual calibration for both pH and EC.A reputation for a rugged build and long lifeSpecialized design for hydroponic, aquaponic, and greenhouse growers.WHAT PEOPLE ARE SAYING"Superb meter, easy to use, great customer service.""Best meter I have ever owned.""The best meter on the market and Milwaukee customer service is the best.""I have owned this meter for almost 8 years and only replaced the probe once. The calibration nobs are easy to use, and even when I am less then gentle with the thing it keeps on going. I wouldn't consider any other meter."CARE AND USEThe MW802 PRO Combo Meter includes both a pH and EC sensor in the SE600 integrated probe. All pH sensors have a limited life and response time gets longer with age. EC sensors are more robust but can still be affected by residue build up. Both need maintenance. Properly maintaining your probe will give you fast, accurate results for longer. So, be sure to order the Milwaukee codes MA9015 and MA9016 at checkout time! This will be needed to help clean and condition the pH/EC electrode before use!Here are our top four tips.1. Always store with the cap full of buffer or storage solution MA9015 not water.2. Clean your probe regularly by soaking in cleaning solution MA9016.3. Calibrate after cleaning and/or storage before testing to adjust for changes in the pH and EC sensor.4. Gently stir the probe in the sample for a faster result.Thank you for considering Milwaukee to help you take your results to the next level.

1 831 kr
Temporarily out of stock
View product
Milwaukee MW600 PRO Dissolved Oxygen Meter with ATC

Milwaukee MW600 PRO Dissolved Oxygen Meter with ATC

The Milwaukee MW600 PRO Portable Dissolved Oxygen meter is one of Milwaukee's most popular meters with its reliable and fast operation as well as its accuracy. The Milwaukee PRO DO Meter is preferred by people looking for lab level accuracy without the cost. The Milwaukee DO Meter is popular with everyone from field biologists and educators to fish farmers and koi pond owners.- Fast, easy-to-read results with large digital LCD readout- Repeatable, accuracy to ±1.5% FS- Lightweight and portable- Simple 2 point open air calibration (see video below)- Uses MA840 reinforced polarographic probe with an oxygen-permeable polytetrafluroethylene (PTFE) membrane sensor- 5 o-rings, membranes and one protective cap included- 10 feet probe cable for extra flexibility when testing- 70 hours of battery life with continuous use (battery included) with low battery warningSPECIFICATIONSO2 Range: 0.0 to 19.9 mg/LO2 resolution: 0.1 mg/LO2 Accuracy: ±1.5% Full ScaleCalibration: Manual on 2 points (zero and slope)Temperature Compensation: Automatic, from 0 to 30°CProbe: MA840 refillable polarographic probe includedMembranes: 5 includedEnvironment: 0 to 50°C / 32 to 122°F; max RH 95%Battery Type: 1 x 9V alkaline (included)Battery Life: Approx. 70 hours of continuous useDimensions: 5.7 x 3.1 x 1.6 inchesWeight: 7.5 ounces with batteryNOTE! You need "Milwaukee MA9070 Solution" to be able to calibrate this meter!CARE AND USE“OPEN AIR” CALIBRATION PROCEDURE1. Remove the membraneTake the membrane off the end of the probe and dry the diode off.2. Zero out the displayConnect the probe to the base unit and turn the unit on. Your display should read 0.0. If it does not, go to the position “0” screw on the front of the unit with the screw driver provided and through the access hole make the unit display read 0.0.3. Fill the membraneGo to the membrane and put the “O” ring inside the membrane on the shoulder at the base of the threads. Fill the membrane to just short of the “O” ring with MA9071 electrolyte solution. Be sure that there are no bubbles inside the membrane. (Air bubbles are the main cause of calibration failure)4. Attach the membraneScrew the membrane on to the probe.5. Let stablizeTurn the meter on and hang the probe off the end of a table pointing down and let the unit display stabilize (this may take 5 to 15 minutes)6. AdjustPush down and hold the “Cal” button on the front face of the meter and with the screwdriver go to the front Cal position “100%” and make the display read 100.You are now calibrated.EXTRA TIPS- Watch for the membrane having wrinkles or stretch marks. If you see wrinkles, replace with a new membrane.- Always use fresh electrolyte solution (MA9071).

1 492 kr
Milwaukee MA9071 Oxygen Electrolyte Solution 230ml

Milwaukee MA9071 Oxygen Electrolyte Solution 230ml

The MA9071 electrolyte fill solution is designed for Milwaukee's polarographic dissolved oxygen probe. A high quality electrolyte solution is crucial to the performance of your dissolved oxygen probe.DESIGN FEATURESPRECISE FORMULATIONFactory mixed using reagent grade chemicals in a dedicated, temperature controlled environment.TRACEABLEProduct labeled with product code, lot number and expiration date.SECUREAir tight bottle with tamper-proof seal.USE AND CARE“OPEN AIR” CALIBRATION PROCEDURE FOR THE MW600 DISSOLVED OXYGEN METER1. Remove the membraneTake the membrane off the end of the probe and dry the diode off.2. Zero out the displayConnect the probe to the base unit and turn the unit on. Your display should read 0.0. If it does not, go to the position “0” screw on the front of the unit with the screw driver provided and through the access hole make the unit display read 0.0.3. Fill the membraneGo to the membrane and put the “O” ring inside the membrane on the shoulder at the base of the threads. Fill the membrane to just short of the “O” ring with MA9071 electrolyte solution. Be sure that there are no bubbles inside the membrane. (Air bubbles are the main cause of calibration failure)4. Attach the membraneScrew the membrane on to the probe.5. Let stablizeTurn the meter on and hang the probe off the end of a table pointing down and let the unit display stabilize (this may take 5 to 15 minutes)6. AdjustPush down and hold the “Cal” button on the front face of the meter and with the screwdriver go to the front Cal position “100%” and make the display read 100.You are now calibrated.EXTRA TIPSWatch for the membrane having wrinkles or stretch marks. If you see wrinkles, replace with a new membrane.Always use fresh electrolyte solution (MA9071).

203 kr
Milwaukee MI56P Replacement Probe for pH55 and pH56 PRO

Milwaukee MI56P Replacement Probe for pH55 and pH56 PRO

The Milwaukee MI56P is the replacement pH/temperature probe (electrode) for the pH55 PRO and pH56 PRO Testers (sold separately). The MI56P probe measures pH and temperature and easily slides into the tester fitting then screws into the meter body for secure installation.

268 kr
Temporarily out of stock
View product
Milwaukee Electrode Rinse Solution 20ml

Milwaukee Electrode Rinse Solution 20ml

Electrode rinse solution (deionised water) is ideal for using as an intermediate rinse between samples or calibration solutions to avoid cross contamination. This rinse solution is also ideal for removing basic salt deposit buildup on the probe or cap caused by storage solution evaporation. Even though salt deposit buildup is normal, it should be removed before measurement or calibration.Electrode rinse solution should not be a substitute for cleaning or storage solutions. Sachet packaging means that you get fresh solution every time. Ideal for infrequent or field use. No risk of using an expired calibration solution. Milwaukee solutions are designed to help you achieve reliable and repeatable measurements while extending the life of your electrode.DESIGN FEATURESElectrode Rinse SolutionFundamental for gently rinsing the electrode between like samples or calibration solutions as well as rinsing off salt deposit buildup.Sealed against light and airIdeal for on-the-spot calibrationSimply open, insert the tester or electrode into the sachet and gently stir

13 kr
Volume discount! 11 kr per piece when you buy 2 or more
Milwaukee Cleaning Solution 20ml

Milwaukee Cleaning Solution 20ml

Cleaning solution is ideal for cleaning all pH, ORP and TDS meter's probes. To help maintain high performance and accuracy for any electrode, regular cleaning is required to remove the build up of dirt and setiment on the glass or carbon surfaces of a sensing probe. Use M10016B to help extend the life of the meter's electrode. Electrode cleaning solution should not be a substitute for rinse and or storage solutions. Sachet packaging means that you get fresh solution every time. Ideal for infrequent or field use. No risk of using an expired calibration solution. Milwaukee cleaning solutions are designed to help you achieve reliable and repeatable measurements while extending the life of your electrode.DESIGN FEATURESFundamental for gently cleaning the electrode between uses and before storage.Sealed against light and air.Ideal for on-the-spot cleaning too.Simply open, insert the tester or electrode into the sachet and gently stir let soak for 15 minutes.

13 kr
Volume discount! 11 kr per piece when you buy 2 or more
Milwaukee Storage Solution 230ml

Milwaukee Storage Solution 230ml

MA9015 is a lab grade electrode storage solution prepared with premium chemicals to improve the performance and extend the life of your pH and ORP electrodes, testers and pens.To ensure a quick response and free-flowing liquid junction, the sensing element and reference junction must not be allowed to dry out. Properly storing your pH electrode in a solution keeps the glass membrane well hydrated which maintains proper function and provides accurate readings.MA9015 also helps keep the junction in your pH and ORP electrode flowing which is critical for fast results.DESIGN FEATURESFundamental for the correct use of electrodes and for obtaining the most accurate and reproducible readings.Formulated to minimize organic growth on your electrode.Sealed against light with air tight, tamper proof cap.Factory blended to precise standards in a dedicated, temperature controlled environment.Simply open and add to the cap of your electrode or tester.

102 kr
Temporarily out of stock
View product
Tilt Replacement Tube

Tilt Replacement Tube

Replacement tube for your Tilt hydrometer. Includes threaded tube, sealing washer, and cap all packaged in our Tilt packaging tube.

135 kr
Tilt Wrench

Tilt Wrench

Tilt wrench is a tool for removing the cap of your Tilt hydrometer. The rubber over-mold keeps the plastic cap intact and free from any scratches or dents while the handle gives you leverage to remove the hard to turn caps. As a bonus the product doubles as a bottle cap remover.

135 kr
Temporarily out of stock
View product
Tilt Replacement Washer

Tilt Replacement Washer

Replacement food grade washer/gasket for the standard Tilt Hydrometer (1.13"/29mm). 1pc.Note: NOT for Tilt PRO.

27 kr
Temporarily out of stock
View product
Pyrex Media Bottle 250ml

Pyrex Media Bottle 250ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 250mlVolume: 250 mlDiameter: 78 mmHeight: 138 mmThread size: 45 mm

135 kr
Pyrex Media Bottle 500ml

Pyrex Media Bottle 500ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 500mlVolume: 500 mlDiameter: 86 mmHeight: 176 mmThread size: 45 mm

169 kr
Pyrex Media Bottle 1000ml

Pyrex Media Bottle 1000ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 1000mlVolume: 1000 mlDiameter: 101 mmHeight: 225 mmThread size: 45 mm

237 kr
Fermtech Wine/Beer Thief Sampler

Fermtech Wine/Beer Thief Sampler

A 'Wine/Beer Thief' is the ideal solution for sampling your beer/wine in a quick and easy way. You can even use it as a measuring cylinder! Made from crystal clear plastic giving you the possibility to evaluate the colour/ clarity and to read your hydrometer. Closes automatically, so no difficult finger exercises! 50 cm long for easy and automatic filling without the need of suction. Hydrometer is not included.Weight 0.08 kgLength 58.2 cmHeight 3.5 cmWidth 10.2 cm

81 kr
Temporarily out of stock
View product
Tilt Pro Replacement Washer 2pcs

Tilt Pro Replacement Washer 2pcs

Replacement food grade washers/gaskets 2pcs for the standard Tilt PRO Hydrometer.Note: NOT for regular Tilt. Pro only.

41 kr
Better Brew Wine Thief Glass 30cm

Better Brew Wine Thief Glass 30cm

A 'Wine/Beer Thief' is the ideal solution for sampling your beer/wine in a quick and easy way. You can even use it as a measuring cylinder! Made from crystal clear glass giving you the possibility to evaluate the colour/ clarity and to read your hydrometer.

34 kr

Funnels Set 50/70/100/115mm Plastic

Funnels Set 50/70/100/115mm Plastic

27 kr

Funnel Plastic 23cm

Funnel Plastic 23cm

41 kr
Wine/Beer Thief Sampler (Enolandia)

Wine/Beer Thief Sampler (Enolandia)

A 'Wine/Beer Thief' is the ideal solution for sampling your beer/wine in a quick and easy way. You can even use it as a measuring cylinder! Made from crystal clear plastic giving you the possibility to evaluate the colour/ clarity and to read your hydrometer. Closes automatically, so no difficult finger exercises! 50 cm long for easy and automatic filling without the need of suction. Hydrometer is not included.

81 kr